Teradata SQL Error and Failure Codes from Error 2633 To 2641

SQLServerF1_Header_Small

2633 Too many load/unload tasks running: try again later
Explanation: This error occurs when more than a certain number (currently 5) of Fast/Multi Loads, FastExport are
simultaneously active.
Generated By: AMP Software.
For Whom: End User.
Notes: This error exists because of the need to set a limit on the number of concurrent Fast/Multi load , FastExport operations.
Check var/adm/streams for more information
Remedy: For fastload resubmit request later. Multiload automatically resubmits when it gets this error.

2634 Existing ERROR table(s) or Incorrect use of %TVMID in Fast Load operation.
Explanation: This error occurs if the table/error table(s) specified either;
(a) existed before the start of the Fast Load, or
(b) did not indicate that it was involved in this specific Fast Load.
Generated By: AMP Software.
For Whom: End User.
Notes: This error means either that the user has referenced existing tables for the ERRORFILES in a Fast Load that is not restarting, or that incorrect tables were referenced in a restart of a Fast Load.
Remedy: If this is not a restart of a previous Fast Load, delete the referenced error files. If this is a restart, correct the
Begin Loading Statement so that the error files are those specified for the original Fast Load.

2635 Error tables are invalid OR %TVMID is in an invalid state for Load – %VSTR
Explanation: This error occurs if the table specified for the Fast/Multi Load is already being used by some other process
(for example, a Dump/Restore or another Fast/Multi Load). This error could also occur if different error tables are specified
for a table whose load job is not completed successfully.
Generated By: AMP Software.
For Whom: End User.
Notes: This error means that the user has referenced a table that another user is using for some other purpose.
Remedy: Find out who is using the named table, or use a different table. If previous load operation on the same table is not completed successfully then check whether error tables are same.

2636 %TVMID must be empty for Fast Loading.
Explanation: This error occurs if the table to be loaded exists and contains data.
Generated By: AMP Software.
For Whom: End User.
Notes: This error means that the user has referenced a table that contains data rows.
Remedy: Delete all the rows in the specified table, or specify a different table.

2637 BEGIN LOADING executed without Fast Load Init.
Explanation: This error occurs when a message is processed to start a Fast Load without the necessary preparation for
the operation.
Generated By: AMP Software.
For Whom: End User.
Notes: This error means either that the user is incorrectly trying to use Fast Load, or that there has been an error in the execution of the Fast Load utility.
Remedy: If the user is not at fault, contact your Support Representative.

2638 No dump image found on system.
Explanation: This error occurs when a request is made to save a system crash dump and there are no dumps to save.
Generated By: AMP Software.
For Whom: Internal Use Only.
Notes: This error means that all AMPs in the system are operational and none of them contains a dump image.
Remedy: This is an internal message, not a user error.

2639 Too many simultaneous transactions.
Explanation: This error occurs if a new transaction is initiated but the system cannot accommodate it.
Generated By: AMP Software.
For Whom: End User.
Notes: This error means that an AMP has as many active transactions as it can hold.
Remedy: Resubmit the request.

2640 Specified table does not exist in %DBID.
Explanation: A table was dropped before a statement that references the table was processed.
Generated By: AMP Software.
For Whom: End User.
Remedy: The table that is referenced no longer exists. If it is needed, it must be re-created.

2641 %DBID.%TVMID was restructured. Resubmit.
Explanation: A table was changed before a statement that references the table was processed. (For example, an index
may have been added or a field removed.)
Generated By: AMP Software.
For Whom: End User.
Notes: The statement may not have the intended result because of the change in the table.
Remedy: Examine the table and resubmit the request.

Above are list of Teradata Errors or Failure Codes from Error 2633 To 2641 received while performing certain operation against Teradata Database or related products.

What are Teradata Database Errors?

In general, each Teradata error message contains the following information:
• The message number.
• The message text. This text is usually returned with the message number. Some messages employ word substitution, where the word substituted represents the system-replacement of a term more specific to the occurrence.
• An explanation of how the error may have occurred.
• Generated-by text that indicates the software module which initiated the message. This field serves a diagnostic purpose for support and development personnel.
• A remedy which suggests how to resolve the condition.

Hope this was helpful.

Thanks,
SQLServerF1 Team
Information about Teradata SQL Error and Failure Codes and Error Messages on Windows, Linux Operating Systems.

 

Leave a Reply

Your email address will not be published. Required fields are marked *