Teradata SQL Error and Failure Codes from Error 2545 to 2555

SQLServerF1

2545 Operation not allowed: %DBID.%TVMID was Rebuilt without fallback.
Explanation: This error occurs only when a user issues a request for a table that was Rebuilt, and the table was not fallback
protected.
Generated By: AMP Steps.
For Whom: End User.
Notes: The table does exist, but their is no data in the table on the rebuilt AMP.
Remedy: Either resubmit the request after the table has been restored, drop the table, or rebuild the table without the
LOCK NO FALLBACK TABLES option.

2549 A read error occurred in a permanent journal table.
Explanation: A disk read error occurred in a permanent journal table. The bad data block cannot be rebuilt automatically
by the Teradata DBS. Manual intervention is required. AMP which detected error will remain offline.
Generated By: RbkCtrl.
For Whom: Operator. DBA. Site support representative.
Remedy: The permanent journal table must be rebuilt. If any user table which journals to this permanent journal table is not defined as dual image, then there will be loss of data in the permanent journal table during the table rebuild. Contact your Support Representative.

2550 MLoad error: bad internal status – %VSTR
Explanation: This error occurs when an internal consistency check fails. The possible inconsistency are: 1) Session status
not in order. 2) MLoad phase status not in order. 3) MLoad state status not in order. 4) Target table is in MLoad state but
WorkTable is missing.
Generated By: AMP Steps.
For Whom: Site support representative.
Remedy: Contact your Support Representative.

2551 MLoad has already been terminated.
Explanation: The MLoad operation on the DBS side has already been terminated. Session is no longer exists.
This problem possible cause is the host MLoad Utility is ignoring the error returned from DBS and still send down data
parcels.
Generated By: AMP MLoad Processing.
For Whom: Host MLoad Utility. Customer Engineer
Notes: The Utility should terminate if there is any error returned while it is sending data parcels to the DBS.
Remedy: Cancel the MLoad job on the Host. Correct the Utility if it is ignoring errors.
Contact your Support Representative, if the user is not at fault.

2552 BEGIN Mload executed without MLoad Init.
Explanation: This error occurs when a message is processed to start a MLoad without the necessary preparation for the
operation.
Generated By: STPEBE
For Whom: End User.
Notes: This error means either that the user is incorrectly trying to use MLoad, or that there has been an error in the execution
of the MLoad utility.
Remedy: If the user is not at fault, contact your Support Representative

2553 Exceed maximum (100) DML Step Limit.
Explanation: DBS received too many DML steps for one MLoad job.
Generated By: AMP MLoad Processing.
For Whom: End User.
Notes: One MLoad operation can only handle up to 100 DML steps.
Remedy: Reduce DML statements in your MLoad job.

2554 Inconsistent situation occurs in restart MLoad – %VSTR
Explanation: Inconsistency encountered in DBS during restarting a MLoad job. The possible inconsistent situations are:
1) The Base work table id maintained in table headers of all target tables are not the same. 2) The target tables given in the
step are not the same as the ones saved in the table headers. 3) The existence of field 4 in table headers of all the MLoad
tables are not consistent. 4) Table already existed when attempting to create default work (WT_) or error (ET_, UV_) tables
in Multiload.
Generated By: STPEBE
For Whom: Site support representative.
Notes: All target tables should share one base work table within a MLoad job. All Mload related tables should have field
4 in their table headers after MLoad steps are processed.
Remedy: Contact your Support Representative.

2555 Table does not belong to the MLoad job.
Explanation: The table does not exist in the given MLoad entry of the load information segment.
Generated By: STPEED
For Whom: MLoad Host Utility.
Notes: BEGIN MLoad should already define all the MLoad tables in the Load information segment before MLOAD step
is processed.
Remedy: Contact your Support Representative.

Above are list of Teradata Errors or Failure Codes from Error 2545 to 2555 received while performing certain operation against Teradata Database or related products.

What are Teradata Database Errors?

In general, each Teradata error message contains the following information:
• The message number.
• The message text. This text is usually returned with the message number. Some messages employ word substitution, where the word substituted represents the system-replacement of a term more specific to the occurrence.
• An explanation of how the error may have occurred.
• Generated-by text that indicates the software module which initiated the message. This field serves a diagnostic purpose for support and development personnel.
• A remedy which suggests how to resolve the condition.

Hope this was helpful.

Thanks,
SQLServerF1 Team
Information about Teradata SQL Error and Failure Codes and Error Messages on Windows, Linux Operating Systems.

 

Leave a Reply

Your email address will not be published. Required fields are marked *