Teradata SQL Error and Failure Codes from Error 10512to 10516

SQLServerF1

10512 Vproc ID is incorrect.
Explanation: The virtual processor identifier in a message address is out of range, identifies an inactive vproc, or specifies
a non-local vproc for a service that can only be performed on a local vproc. This is probably caused by a coding error in
the program logging the event.
Generated By: PDE message subsystem.
For Whom: System Support Representative.
Notes: This event normally causes an automatic DBS restart.
The associated stack trace will help the Global Support Center determine the exact cause of the failure.
Remedy: Contact the Global Support Center.

10513 Message cannot be routed.
Explanation: A message was received from the TDN subsystem (at interrupt) for delivery to a mailbox that is not
defined. This may be due to a timing problem, where the task to receive the message has not yet run to the point where it
creates the mailbox, or a task is unaware that the task it is sending a message to is about to terminate.
Generated By: PDE message subsystem.
For Whom: System Support Representative.
Notes: This message is only written to the log file and DBS event log. It does not appear on the console.
Remedy: In some cases, these events are not important. If the task sending a message will reissue it when there is no
response, for example, the system will continue to run normally.
If the event appears to be associated with a hung session, is repeated frequently, or otherwise appears to indicate a real
problem, contact the Global Support Center.

10514 Non-host message sent to external transient mailbox.
Explanation: External transient mailboxes allocated with msggtbxe() should only be used by host communications. The
message subsystem does not recognize this message as a host message but it will attempt delivery.
Generated By: PDE message subsystem.
For Whom: System Support Representative.
Notes: The associated stack trace will help the Global Support Center determine the exact cause of the failure.
Remedy: Although this may have no effect on the DBS, it indicates an error in the logic of the program logging it, which
should be reported to the Global Support Center.

10515 Message is too long.
Explanation: Attempted to send a message that exceeds 1 MB, or 32 KB in the case of a host message. This is usually
caused by an error in the logic of the program logging the event.
Generated By: PDE message subsystem.
For Whom: System Support Representative.
Notes: This event normally causes an automatic DBS restart.
The associated stack trace will help the Global Support Center determine the exact cause of the failure.
Remedy: Contact the Global Support Center.

10516 Segment is sharable.
Explanation: A shareable segment was passed to msgtxseg(), requesting that it be discarded after being sent. This is not
allowed because another task could access the segment, so it cannot be discarded. This is usually caused by an error in the
logic of the program logging the event.
Generated By: PDE message subsystem.
For Whom: System Support Representative.
Notes: This event normally causes an automatic DBS restart.
The associated stack trace will help the Global Support Center determine the exact cause of the failure.
Remedy: Contact the Global Support Center.

Above are list of Teradata Errors or Failure Codes from Error 10512to 10516 received while performing certain operation against Teradata Database or related products.

What are Teradata Database Errors?

In general, each Teradata error message contains the following information:
• The message number.
• The message text. This text is usually returned with the message number.
Some messages employ word substitution, where the word substituted
represents the system-replacement of a term more specific to the
occurrence.
• An explanation of how the error may have occurred.
• Generated-by text that indicates the software module which initiated the
message. This field serves a diagnostic purpose for support and
development personnel.
• A remedy which suggests how to resolve the condition.

Hope this was helpful.

Thanks,
SQLServerF1 Team
Information about Teradata SQL Error and Failure Codes and Error Messages on Windows, Linux Operating Systems.

 

Leave a Reply

Your email address will not be published. Required fields are marked *